Free Construction Tool

Chimney Calculator

Reviewed and updated: August 2026

Calculate flue liner size, chimney brick count, mortar, and required chimney height for any fireplace opening or wood stove. Includes IRC 2-3-10 height and clearance rules.

The flue must be sized to at least 1/10 of the fireplace opening area (or 1/12 for round flues). Enter your fireplace opening dimensions.

in
in
Affects draft, taller = better draw
ft
ft
$

IRC 2-3-10 rule: chimney must extend 3 ft above roof penetration and 2 ft above any part of the building within 10 ft horizontally.

Horizontal distance from chimney to ridge
ft
YOUR RESULTS

This calculator covers three chimney planning needs: sizing the flue liner based on your fireplace opening (Flue Size tab), estimating bricks, mortar, and flue tile sections for the above-roof chimney section (Brick Count tab), and checking IRC height clearance requirements based on your roof pitch and chimney location (Height Rules tab).

Flue Sizing Rules

The flue cross-sectional area must equal at least 1/10 of the fireplace opening area for rectangular clay tile flues, or 1/12 for round metal flues. A larger flue is better than a smaller one, oversizing by 10–20% improves draft. Undersizing causes smoke spillage into the room.

Worked example: a 36×28 inch fireplace opening has an area of 1,008 sq in. Minimum flue area = 1,008 ÷ 10 = 100.8 sq in. A standard 12×12 inch clay flue tile has an actual inside area of approximately 113 sq in, the smallest standard size that meets this requirement. An 8×12 inch tile (actual ~75 sq in) would be undersized for this opening.

Standard Flue Liner Size Reference

Flue LinerActual Inside AreaMax Fireplace OpeningTypical Application
8" × 8"~50 sq in500 sq in (e.g. 24"×20")Small fireplace or wood stove
8" × 12"~70–77 sq in750 sq in (e.g. 30"×25")Small to medium fireplace
12" × 12"~113 sq in1,130 sq in (e.g. 36"×31")Standard 36" fireplace
13" × 13"~127 sq in1,270 sq in (e.g. 40"×31")Medium-large fireplace
13" × 17"~162 sq in1,620 sq in (e.g. 48"×33")Large fireplace opening
17" × 17"~216 sq in2,160 sq in (e.g. 60"×36")Very large or double-sided
8" round~50 sq in600 sq in (1/12 rule)Small metal liner for gas
10" round~78 sq in936 sq in (1/12 rule)Medium gas or wood stove
12" round~113 sq in1,356 sq in (1/12 rule)Larger gas or oil appliance

The 2-3-10 Chimney Height Rule

The IRC requires two conditions both be met: the chimney cap must extend at least 3 ft above the point where the chimney exits the roof, and it must extend at least 2 ft above any part of the roof structure within 10 ft horizontally. Whichever measurement produces the taller chimney governs.

On a 6/12 pitch roof with the chimney 8 ft from the ridge: the rise at 10 ft from the chimney toward the ridge = 10 × (6/12) = 5 ft. Minimum height = max(3, 2 + 5) = 7 ft above the roof penetration. On a flat or low-pitch roof near the center, the 3 ft minimum usually governs and the chimney only needs to clear that threshold.

Chimney Materials

ComponentStandard SpecificationNotes
Chimney brickHard-fired face brick, SW gradeSW = severe weathering; required in freeze-thaw climates
Mortar (joints)Type S, 3/8" jointsNever use Type N on exterior chimney
Flue liner (new)ASTM C315 clay tileStandard 2 ft sections; sold at masonry suppliers
Flue liner (retrofit)316L stainless flexible linerFor wood; use 304 SS for gas and oil
Chimney capCast stone or precast concreteExtends 2–4" beyond chimney on all sides to shed water
FlashingStep + counter flashing, 26-gauge lead or copperMost critical waterproofing detail, do not use aluminum

Common Chimney Mistakes

Safety note: Chimney design and construction involves life-safety considerations, fire, carbon monoxide, and structural integrity. The calculations in this tool are planning-level estimates based on IRC guidelines. Any new chimney construction or major liner replacement should be inspected by a Certified Chimney Sweep (CSIA) or reviewed by a licensed mason familiar with your local code. Never connect a wood stove or fireplace insert to an unlined chimney.

Chimney and Flue Diagram

The diagram below shows the 2-3-10 rule that governs chimney height above the roofline. This rule applies to all fuel-burning appliances vented through a masonry chimney under IRC R1003.9.

3 ft min above penetration 2 ft min above ridge / any structure within 10 ft horizontal 10 ft horizontal radius CHIMNEY flue liner inside

2-3-10 rule per IRC R1003.9 · 3 ft above roof penetration · 2 ft above any structure within 10 ft horizontal

Fireplace and Appliance Draft Requirements

Draft is the negative pressure that pulls combustion gases up and out of the chimney. Adequate draft requires the right combination of flue size, chimney height, and temperature differential. A chimney that is too short, too large, or in poor thermal condition will backdraft, pushing smoke into the room instead of exhausting it.

FactorEffect on DraftPractical Note
Chimney heightTaller = stronger draftMinimum 15 ft total height from firebox to cap; 20+ ft preferred for wood-burning
Flue areaCorrect size = optimal draft; oversized = weak draft1/10 rule minimum for rectangular, 1/12 for round; oversizing by 10% is fine
Flue temperatureHotter = stronger draftCold flues cause startup smoke; preheat with paper before lighting
Negative house pressureTightly sealed houses resist draftOpen a window slightly if persistent backdraft occurs in tight homes
WindDowndraft on lee side of roofChimney cap with wind collar recommended where prevailing wind is an issue
ObstructionsTrees, additions within 10 ft can cause downdraftObserve the 2-3-10 rule; cap type matters near obstructions

Flue Liner Types and Applications

The flue liner is the interior conduit that channels combustion gases from the appliance to the outside. It must be matched to the fuel type and appliance being vented. Using the wrong liner type is a serious fire hazard and building code violation.

Liner TypeFuel TypesLifespanNotes
Clay tile (standard)Wood, oil, coal50+ years if maintainedMost common; must be intact, cracked tiles allow combustion gases into masonry and framing
Cast-in-place (poured)All fuel types50+ yearsBest for relining irregular or deteriorated chimneys; creates seamless liner
Stainless steel flexibleGas, oil, wood pellets15–25 yearsCommon for relining; must match liner alloy to fuel type (AL29-4C for gas, 316L for oil/wood)
Rigid stainlessGas, oil25+ yearsBetter than flexible but requires straight chimney sections
Aluminum flexibleGas only (Category I)15–20 yearsLeast expensive; only approved for non-positive pressure gas appliances

Chimney Inspection and Maintenance Schedule

The National Fire Protection Association (NFPA 211) and most building codes require annual chimney inspection. Creosote buildup in wood-burning chimneys is a leading cause of house fires. Here is the standard maintenance schedule:

TaskFrequencyWho Does It
Visual inspectionAnnually (spring or fall)Certified chimney sweep (CSIA)
Cleaning (wood-burning)When creosote reaches 1/8"Certified chimney sweep
Gas appliance inspectionAnnuallyCertified sweep or HVAC technician
Cap and crown inspectionEvery 2–3 yearsSweep or mason
Tuckpointing (mortar joints)When cracking or spalling visibleMasonry contractor
WaterproofingEvery 5–7 yearsSweep or mason
Full Level 2 inspectionBefore purchase, after fire or earthquakeCSIA-certified sweep with camera

For further information on fireplace and chimney safety, see the project cost estimation guide for budgeting chimney repair and maintenance work.

Frequently Asked Questions
What size flue do I need for a 36-inch fireplace? ▾
A 36" wide × 28" tall fireplace opening = 1,008 sq in. Using the 1/10 rule: minimum flue area = 100.8 sq in. A 12×12" clay flue tile (actual inside area ~113 sq in) is the standard minimum choice. For fireplaces with a shallow firebox depth or any situation where draft is a concern, step up to a 13×13" tile (~127 sq in) for better performance. Never use an 8×12" tile (only ~75 sq in) for this opening size.
How high does a chimney need to be? ▾
The IRC 2-3-10 rule requires: (1) at least 3 ft above the roof penetration point, and (2) at least 2 ft above any part of the roof structure within 10 ft horizontally. Both conditions must be checked, the taller result governs. On a 6/12 pitch roof with the chimney 8 ft from the ridge, the required height is 7 ft above the roof exit. On a flat roof near the center of the building, the 3 ft minimum usually governs.
Can I use flexible liner to reline a chimney? ▾
Yes, stainless steel flexible liner is code-approved and widely used for relining damaged or undersized masonry chimneys. It's inserted from the top and connected to the appliance at the bottom. Use 316L stainless for wood-burning applications; 304 stainless is acceptable for gas and oil. Size the liner to the appliance's listed flue collar size, not the old flue dimensions, most wood stoves specify a 6" or 8" flue collar and the liner must match.
How many bricks does a chimney use per foot of height? ▾
A standard 16×16 inch outside-dimension chimney (single flue) uses approximately 16 standard bricks per vertical foot of height. The perimeter is 64 inches (16×4), each brick face is 8×2.25 inches with 3/8" mortar joints, giving roughly 3.3 courses per foot × 4–5 bricks per course. For a 6 ft above-roof chimney section, that's about 96 bricks plus 5% waste = 101 bricks. Use the Brick Count tab for your specific chimney dimensions.
What is the difference between a clay tile liner and a metal liner? ▾
Clay tile liners (ASTM C315) are the traditional choice for new masonry chimneys, they're installed in 2 ft sections as the chimney is built, are very durable when properly installed and maintained, and handle the temperatures of wood fires well. Metal flexible liners are used primarily for retrofitting existing chimneys that are damaged, undersized, or being converted to a different fuel. Metal liners are faster to install and can navigate slight bends, but must be correctly sized for the appliance and maintained with regular inspections. Gas appliances always require a metal liner if the existing clay tile was originally used for wood, due to condensate acidity.