Free Construction Tool

Slope Calculator – Grade %, Angle, Ratio & Rise

Reviewed and updated: August 2026

Convert between grade percentage, angle in degrees, and slope ratio. Calculate rise, run, and slope length for ramps, driveways, drainage, and site grading.

Select your input type, enter a value and run length, and choose your application for a complete slope breakdown including ADA compliance check and drainage adequacy notes.

Choose how you know the slope
e.g. 8.33 for 1:12 ADA ramp
%
Horizontal distance
ft
For compliance and guidance notes
SLOPE RESULTS
Grade
—
percent (%)
Angle
—
degrees
Ratio
—
1 : X (rise : run)
Rise over Run
—
vertical change
Rise in Inches
—
inches per foot of run
Slope Length
—
ft (along slope)
ADA Compliance
—
Drainage Adequacy
—

Understanding Slope: Grade, Angle, and Ratio

Slope is the relationship between vertical rise and horizontal run, but it can be expressed three different ways depending on the application. Understanding which expression is used in your context avoids costly errors in layout and specification.

Grade Percentage (%)

Grade percentage is rise divided by run, multiplied by 100. A 5% grade rises 5 feet for every 100 feet of horizontal distance, or 0.6 inches per foot. Grade percentage is the standard expression for roads, driveways, drainage, site grading, and ADA accessibility. It's the most intuitive for construction because it directly tells you how many inches or feet you gain over a given distance.

Grade % = (rise ÷ run) × 100

Angle in Degrees

Angle is the arctangent of rise over run, expressed in degrees from horizontal. A 5% grade equals about 2.86°. Angles are used in structural engineering, geotechnical reports, and some survey documents. They're rarely used directly in construction layout but are useful for setting saw bevel angles on angled cuts for ramp stringers or sloped framing.

Angle = arctan(rise ÷ run)

Ratio (1:X)

A slope ratio expresses how many units of horizontal run there are for every 1 unit of rise. A 1:12 ratio means 1 inch of rise for every 12 inches of run, the maximum ADA ramp slope. A 1:20 ratio is 1 inch of rise per 20 inches of run (5% grade). Ratios are commonly used in accessibility standards, road design, and some drainage specifications.

Ratio (1:X) = run ÷ rise

Grade %AngleRatio (1:X)Rise per 12" runCommon Use
1%0.57°1:1000.12"Minimum pavement drainage
2%1.15°1:500.24"Standard pavement / patio slope
5%2.86°1:200.60"Walkways, gentle grading
8.33%4.76°1:121.00"Maximum ADA ramp slope
10%5.71°1:101.20"Steep walkway, gentle driveway
15%8.53°1:6.71.80"Moderate driveway
20%11.31°1:52.40"Steep driveway (caution)
25%14.04°1:43.00"Maximum residential driveway
50%26.57°1:26.00"6/12 roof pitch
100%45.00°1:112.00"12/12 roof pitch (45°)

How to Calculate Slope

The three core slope calculations all derive from the same right triangle, rise (vertical), run (horizontal), and slope length (hypotenuse).

Rise = run × (grade % ÷ 100)

Slope length = √(rise² + run²)

Angle = arctan(rise ÷ run)

For example: a 20-foot run at 8.33% grade has a rise of 20 × 0.0833 = 1.67 feet (20 inches). The slope length is √(1.67² + 20²) = 20.07 feet, barely longer than the horizontal run at this gentle slope. At steeper grades (15%+), the slope length becomes meaningfully longer than the run and matters for material takeoffs on ramp stringers or drainage pipe.

ADA Ramp Requirements

The Americans with Disabilities Act (ADA) and the ADA Standards for Accessible Design set specific slope requirements for ramps in public accommodations, commercial facilities, and other covered buildings. Residential construction is generally not covered by ADA, but many local codes and universal design standards reference the same thresholds.

RequirementADA StandardNotes
Maximum ramp slope1:12 (8.33%)1" rise per 12" run
Maximum cross slope1:48 (2.08%)Perpendicular to direction of travel
Maximum rise per run30 inchesRequires landing before continuing
Minimum ramp width36 inches clearBetween handrails
Landing size60" × 60" minAt top, bottom, and direction changes
Handrails required whenRise > 6 inchesBoth sides, 34"–38" height
Edge protectionRequiredCurb, rail, or barrier at open sides

A ramp with more than 30 inches of total rise must include intermediate landings, each landing breaks the run into segments no taller than 30 inches. For example, a 4-foot total rise (48 inches) requires at least two 24-inch segments with a landing between them, or one 30-inch segment plus one 18-inch segment.

Driveway Slope Guidelines

Driveway slope affects drainage, vehicle clearance, safety in wet and icy conditions, and garage floor transitions. There is no single national standard, requirements vary by municipality, but general guidelines are widely consistent.

Driveways that slope toward the garage require a drainage channel (trench drain) at the base to prevent water from entering. This is a common oversight that leads to wet garages and foundation issues over time.

Drainage and Grading Slopes

Proper site grading is one of the most important, and most often neglected, aspects of residential construction. Water that doesn't drain away from the foundation will eventually find its way in.

Foundation Grading

The International Residential Code (IRC) requires the ground surface to slope away from the foundation at a minimum of 6 inches in the first 10 feet, that's a 5% grade. Many builders target 6–8% for the first 10 feet to provide a safety margin for soil settlement. Beyond 10 feet, the grade can flatten to 2%.

Hardscape and Patio Slopes

Concrete patios, pavers, and other hardscape surfaces should slope away from the structure at a minimum of 1–2% (1/8" to 1/4" per foot). Surfaces that drain toward the house, or that are dead flat, will pool water and create freeze-thaw damage at the house wall over time.

Swales and Drainage Channels

Grass swales that carry water across a site should maintain a minimum 1–2% grade to keep water moving and prevent standing water and mosquito breeding. Steeper swales (5%+) may need erosion protection such as sod, riprap, or erosion blanket to prevent channel scour.

Road and Site Grading

Commercial sites, parking lots, and roadways follow different slope standards than residential construction.

Common Slope Mistakes

Planning Grading and Ramp Costs

Site grading costs vary widely based on scope, soil conditions, equipment access, and whether fill needs to be imported or exported. Basic finish grading around a new home runs $500–$3,000. Ramp construction costs range from $1,000–$3,500 for a simple wood or concrete residential ramp to $8,000–$20,000+ for a fully ADA-compliant commercial ramp with landings, handrails, and edge protection.

Need help estimating total project cost? Read our project cost estimation guide.

Slope Diagram, Rise, Run, and Grade

Slope is a relationship between vertical rise and horizontal run. All three expressions (grade percentage, angle, and ratio) describe the same physical slope, they are just different ways of stating the same number.

RISE RUN (horizontal) angle° FORMULAS Grade % = rise/run × 100 Angle = arctan(rise/run) Ratio = 1 : (run/rise) Slope = √(rise²+run²)

All three expressions describe the same slope · Grade % is most common in construction · Ratio is used in accessibility standards

Slope Requirements by Application

Different applications have different slope requirements driven by code, safety, or drainage function. Here is a reference for the most common applications:

ApplicationMin SlopeMax SlopeStandard / Source
ADA accessibility rampNone (flat OK)8.33% (1:12)ADA Standards 405.2
ADA accessible route (walk)None5% (1:20)ADA Standards 403.3
Concrete patio (drainage)1% (1:100)2% typicalACI 302.1R
Concrete driveway1%15% typical; 20% maxLocal code varies
Asphalt pavement2% cross slope6% longitudinalAASHTO design guides
Swale / drainage channel1% (0.5% min)No maximum (velocity governs)Civil engineering practice
Lawn / turf grading2% away from structure3:1 (33%) for mowable slopeIRC R401.3; landscape practice
Foundation grading6 inches fall in 10 ftNo maximumIRC R401.3
Road centerline0.5%12% residential; 7% collectorAASHTO; local subdivision codes

ADA Ramp Design Requirements

ADA ramp compliance involves more than just the maximum 1:12 slope. A complete ADA ramp requires specific dimensions at every element:

ElementADA RequirementNotes
Maximum slope1:12 (8.33%)Steeper slopes require handrails and landings
Maximum rise per run30 inches per ramp segmentA 30" rise requires at least 30 ft of ramp at 1:12
Minimum clear width36 inches60 inches preferred for two-way passage
Landing at top and bottom60 inches × 60 inches minimumRequired at every change of direction
HandrailsRequired on both sides if rise exceeds 6 inches34–38 inches above ramp surface; 1.25–2 inch graspable diameter
Edge protection2 inch curb or barrier on open sidesPrevents wheelchair wheels from going off edge
SurfaceStable, firm, slip-resistantBroom-finished concrete or textured asphalt typical
Cross slopeMaximum 2% (1:50)Perpendicular to travel direction

Drainage Slope, How Much Is Enough?

Drainage slope requirements depend on the material and what is draining. Concrete and asphalt pavements need a minimum 1% slope to drain reliably, less than 1% causes puddles that don't drain, leading to freeze-thaw damage and slip hazards. Landscape grading around foundations requires a minimum 6-inch fall within the first 10 feet away from the structure, per IRC R401.3, to direct water away from the foundation.

For drainage swales and channels, minimum slope is typically 0.5–1% to maintain self-cleaning velocity. Slopes below 0.5% allow sediment to accumulate and eventually block the channel. Above about 15%, surface erosion becomes a concern and the channel may need to be armored with stone or riprap.

For grading and site drainage calculations, see our project cost estimation guide.

Frequently Asked Questions
What is the maximum slope for an ADA-compliant ramp? ▾
The maximum slope for an ADA-compliant ramp is 1:12, one inch of rise for every 12 inches of horizontal run, which equals 8.33%. In practice, most accessibility consultants recommend designing to 1:14 or 1:16 to account for surface irregularities and construction tolerances. Any ramp with a rise greater than 6 inches also requires handrails on both sides, and runs that exceed 30 inches of total rise require an intermediate landing at least 60 inches long.
What is the minimum slope for proper drainage? ▾
For hardscape surfaces like concrete, pavers, and asphalt, a minimum slope of 1–2% (1/8" to 1/4" per foot) is recommended to ensure water drains off the surface and doesn't pool. For foundation grading, the IRC requires a minimum 5% slope (6 inches in the first 10 feet) away from the structure. Grass swales and drainage channels should maintain at least 1–2% to keep water moving. Flat or reverse-sloped surfaces are one of the most common causes of chronic moisture problems in residential construction.
What is a 2% slope in inches per foot? ▾
A 2% slope equals 0.24 inches of rise per foot of horizontal run, just under 1/4 inch per foot. This is a very gentle slope that's nearly imperceptible to the eye but is enough to drain water off a flat surface like a patio, sidewalk, or parking lot. To convert any grade percentage to inches per foot, multiply the percentage by 0.12. So a 5% grade = 5 × 0.12 = 0.60 inches per foot, and a 8.33% ADA ramp = 8.33 × 0.12 = 1.00 inch per foot.
What is the difference between slope, grade, and pitch? ▾
All three describe the steepness of a surface, but they're expressed differently. Grade is a percentage, rise divided by run times 100. Slope is a general term that can refer to grade, angle, or ratio depending on context. Pitch typically refers to roof slope and is expressed as rise per 12 inches of run (e.g., 6/12 pitch). A 6/12 pitch equals a 50% grade and a 26.6° angle. In everyday construction, grade is used for site work and civil applications, while pitch is used for roofing and framing.
What is the maximum driveway slope? ▾
Most municipalities cap residential driveways at 20–25% maximum slope, though some allow up to 30% in specific circumstances. For practical comfort and safety, slopes above 15% become challenging for low-clearance vehicles and hazardous in icy conditions. The recommended range for most driveways is 2–12%. The apron (the transition zone where the driveway meets the street) should flatten to 5% or less regardless of the main driveway slope to prevent vehicles from bottoming out. Always check local zoning and public works requirements before designing a steep driveway.