Calculate cubic yards, tons, and 50 lb bag equivalents for play sand, mason sand, concrete sand, polymeric sand, and leveling sand. Includes material cost estimate.
ft
ft
in
$
YOUR RESULTS
Cubic yards
—yd³
Tons
—tons
Cubic feet
—ft³
Material cost
—
50 lb bags equivalent
—bags
This calculator covers five common sand types used in construction and landscaping. Enter your area dimensions and depth, choose the right sand type, and get cubic yards, tons, and an estimated material cost. A 10% overage buffer is built in to account for compaction and waste.
How to Calculate Sand Needed
Start by measuring your area's length and width in feet, then decide on a depth in inches. Multiply length × width × (depth ÷ 12) to get cubic feet, divide by 27 for cubic yards, and multiply by the sand's density to get tons. Our calculator handles all of this automatically and adds a 10% buffer: because sand compresses during installation and you'll always lose some on the edges.
For a worked example: you're laying a 15 × 10 ft paver patio with a 1-inch sand bedding layer. The raw volume is 15 × 10 × (1 ÷ 12) = 12.5 cubic feet. With the 10% buffer: 13.75 cubic feet = 0.51 cubic yards. At a density of 1.6 t/yd³ for concrete sand, that's 0.82 tons, which at $40/ton comes to about $33 in material cost. You'd need roughly 33 bags if buying bagged.
From Dimensions to Delivery: The Conversion Chain
Every result on this calculator flows through the same four-step chain, and understanding it helps you sanity-check any number a supplier quotes you.
The only variable that changes between sand types is density (tons per cubic yard). Everything else in the chain is the same math.
Sand Grain Size and Why It Matters
Not all sand grains are the same shape, and that difference is what separates a structural material from a soft, decorative one. Sand is classified partly by particle size distribution, tested with a stack of sieves of decreasing mesh size, but the practical distinction that matters most for a homeowner is angular versus rounded grains.
Concrete and paver base sand (often called "sharp sand") has angular, irregular particles that lock together mechanically under compaction, similar to interlocking puzzle pieces. Play sand and some mason sands are washed and tumbled to be rounded and smooth for safety and texture, which unfortunately also means the grains slide past each other under load instead of locking. That's the entire reason play sand fails as a structural base material: it's a shape problem, not a quality problem.
Sand Types and Best Uses
Choosing the wrong sand type is one of the most common, and costliest, mistakes on a project. Here's a quick reference for each type covered by this calculator:
Sand Type
Density (t/yd³)
Best Use
Notes
Play sand
1.35
Sandboxes, play areas
Washed, rounded grains: safe and soft underfoot
Mason sand
1.50
Mortar, stucco, between pavers
Fine texture; smoother than concrete sand
Concrete sand
1.60
Concrete aggregate, paver base
Coarse, angular grains for better compaction and bond
Polymeric sand
1.45
Locking paver joints
Contains binders that harden when wet; prevents weeds
Leveling sand
1.40
Base under pavers, tile, turf
Fine and consistent: used purely for flat bedding
Recommended Depths by Application
Application
Recommended Depth
Notes
Paver bedding (walkway)
1 inch
Do not exceed 1.5": thicker beds shift
Paver bedding (driveway)
1 inch
Use concrete sand, not mason sand
Sandbox fill
6–12 inches
Deeper is safer for fall cushioning
Between flagstones
Fill joint depth
Polymeric sand recommended for longevity
Under artificial turf
¾–1 inch
Leveling sand for drainage and flatness
Concrete mix (aggregate)
Per mix design
Typically 1 part cement : 2 parts sand : 3 parts gravel
Mortar (brick/block)
3/8" joints
Mason sand preferred for smooth consistency
How to Check Sand Quality Before You Buy
Not all sand from a given supplier is consistent, and visually inspecting a pile doesn't tell you much about what's mixed into it. A simple field test, borrowed from soil science, can flag problems before a truckload gets dumped in your driveway:
The jar test: fill a clear jar about one-third with a sand sample, add water to nearly full, shake vigorously, then let it settle for a few minutes. Sand settles first (within seconds), silt settles next (within a few minutes), and clay stays suspended or settles last as a fine layer on top. A thick cloudy layer or a layer of fine sediment on top signals significant silt or clay content, which weakens concrete, reduces mortar bond strength, and can cause staining under pavers.
Visual color check: sand with a notably reddish, brown, or grayish tint (versus tan or light gray) often has higher clay or organic content. This isn't a strict rule, since natural sand color varies by region and source, but it's worth asking the supplier about if the color looks unusual for their normal product.
Smell test: a musty or earthy smell suggests organic matter or contamination, which can rot, attract insects, or create voids as it decomposes under a structural application.
Ask for a gradation sheet: reputable suppliers of concrete and mason sand can provide a sieve analysis (particle size distribution) showing the sand meets ASTM C33 (concrete sand) or ASTM C144 (mason sand) specifications. This is standard practice for commercial suppliers and worth asking for on any structural project.
These checks matter most for structural applications (concrete, mortar, paver base) where contamination directly affects strength and longevity. For decorative uses like sandboxes or leveling, minor silt content is much less consequential.
Bags vs. Bulk Sand
Under 0.5 tons (roughly half a cubic yard), buying 50 lb bags from a hardware store is most convenient and costs about $5–8 per bag. Over 1 ton, bulk delivery from a landscape or masonry supplier is significantly cheaper: typically $25–50 per ton delivered, or 30–50% less than bagged sand per unit volume. For paver base projects requiring several tons, always order bulk.
Common Mistakes When Ordering Sand
Using the wrong sand type under pavers. Mason sand and play sand are too fine and too compressible for structural paver bases. Use concrete sand (ASTM C33 gradation) for any load-bearing paver application.
Setting the bedding layer too thick. More than 1.5 inches of sand under pavers creates an unstable base that allows pavers to rock and sink over time. The gravel base provides the depth: the sand layer is for fine-leveling only.
Forgetting the 10% overage. Sand settles and compresses 5–15% depending on type and compaction effort. Always order at least 10% more than your raw calculation.
Not accounting for moisture. Wet sand is noticeably heavier than dry. If you're ordering by the ton and the supplier's sand is wet from rain, you'll receive less volume than expected. Check the moisture condition and adjust if needed.
Applying polymeric sand in wet conditions. Polymeric sand must be installed dry and then activated with a single watering. If applied to wet joints or caught in rain before it sets, it can cure unevenly and fail to lock properly.
Supplier tip: When ordering bulk sand, always ask whether the price is per ton or per cubic yard: suppliers differ. Also ask whether the sand is washed and what the gradation is. Unwashed sand can contain clay and silt that compromise mortar strength and cause staining on pavers.
Bag count depends on total weight, since bags are sold by weight (50 lb) rather than a fixed volume. For a 10×10 ft area at 2 inches deep using play sand (18.3 cu ft including the 10% buffer, about 0.68 cubic yards), that works out to roughly 0.92 tons, or about 37 bags. Denser sand types need more bags for the same volume. Use this calculator with your exact dimensions and sand type for a precise bag count.
How many cubic yards is a ton of sand? ▾
It depends on sand type. Play sand: 1 ton ≈ 0.74 cubic yards. Concrete sand: 1 ton ≈ 0.63 cubic yards. Mason sand: 1 ton ≈ 0.67 cubic yards. This calculator applies the correct density for your selected sand type automatically, so you get an accurate ton estimate rather than a one-size-fits-all number.
How deep should sand be under pavers? ▾
The standard sand bedding depth under pavers is 1 inch of compacted concrete sand (ASTM C33). Do not exceed 1.5 inches: thicker sand beds allow pavers to rock and settle unevenly under traffic. The structural depth comes from your compacted gravel base (4 inches for walkways, 6–8 inches for driveways), not from the sand layer.
What's the difference between concrete sand and mason sand? ▾
Concrete sand (also called sharp sand) has coarser, angular particles with a larger gradation range: it's designed as aggregate for concrete and as a structural paver base. Mason sand is finer and more uniform, giving a smoother texture ideal for mortar, stucco, and between flagstone joints. Don't substitute one for the other in structural applications: concrete sand is significantly better at resisting compressive loads.
Can I use play sand as a paver base? ▾
No. Play sand particles are round and fine: they don't interlock under compaction, which makes them a poor choice for any structural application. Under pavers, play sand will shift and allow the pavers to settle unevenly within one or two freeze-thaw cycles. Always use concrete sand (ASTM C33) for paver bedding and base applications.
How much sand do I need for a sandbox? ▾
A standard 4×4 ft sandbox filled 8 inches deep needs about 0.4 cubic yards of play sand, roughly 0.53 tons. Deeper fill (10 to 12 inches) is safer for fall cushioning under play structures and swing sets, and is often required by playground safety guidelines for equipment with a fall height over 4 feet. Always use washed, screened play sand rated safe for children, not construction-grade sand, which can contain silica dust and sharp particles.
Does sand weight change when it's wet? ▾
Yes, significantly. Wet sand can weigh 20 to 25% more than dry sand of the same volume due to absorbed water, though very saturated sand can occasionally weigh slightly less per volume due to bulking (water films pushing grains apart). If you're ordering sand by weight (tons) rather than volume, ask your supplier about current moisture content, especially after rain, since a load quoted by weight will contain less actual dry sand volume than the same weight of dry material.