Reviewed and updated: August 2026
Estimate truss count, peak height, top and bottom chord length, approximate weight, and total cost for any building span, pitch, spacing, and truss type.
Use these results as a planning reference. Always confirm final truss specifications with your truss manufacturer; engineered drawings are required for permitted construction.
A roof truss is a prefabricated, engineered structural frame that spans from wall to wall and supports the roof load. Unlike site-built rafter-and-ridge construction, trusses are manufactured in a controlled factory environment using precision-cut lumber and metal connector plates. They arrive on-site ready to set, which dramatically reduces framing labor compared to stick-framing a roof.
Trusses work by distributing loads through a triangulated web of top chords (the sloped members that form the roof surface), bottom chords (the horizontal member that ties the base), and web members (internal diagonals and verticals that transfer load between them). The triangle is the most structurally efficient shape: it cannot deform under load without a member changing length.
Because trusses are engineered components, they must never be cut, notched, or modified in the field without written authorization from the truss manufacturer's engineer of record. Even a small notch in a web member can compromise the entire truss.
The right truss type depends on your ceiling profile, attic use, span, and load requirements. Most residential construction uses one of four common configurations.
| Truss Type | Ceiling Profile | Attic Use | Best For |
|---|---|---|---|
| Fink / W-truss | Flat | Limited (web obstruction) | Standard residential, most common |
| Howe truss | Flat | Limited | Longer spans, heavier loads |
| Scissor truss | Vaulted / cathedral | None | Open-plan living spaces, great rooms |
| Attic truss | Flat with raised center | Full room or storage | Bonus rooms, storage, ADUs above garage |
| Mono truss | Single slope | None | Shed roofs, additions, porches |
| Hip truss set | Flat | Limited | Hip roof systems, requires full set design |
The Fink truss is the workhorse of residential construction. Its W-shaped web pattern efficiently transfers load with minimal lumber, making it the most economical option for standard gable roofs up to about 40 feet. The web configuration leaves limited attic access but is perfectly adequate for insulation and mechanical runs.
A scissor truss has sloped bottom chords that create a vaulted ceiling effect without the complexity of cathedral rafter construction. The bottom chord pitch is typically half the roof pitch: on a 6/12 roof, the bottom chord might slope at 3/12. Scissor trusses carry higher thrust forces at the bearing points and require careful wall design to handle the outward push.
Attic trusses have a raised rectangular opening in the center web that creates usable floor space within the truss depth. They're significantly heavier and more expensive than standard trusses but can add substantial livable or storage square footage. The minimum span for a useful attic opening is typically around 26 feet.
Peak height is determined entirely by the half span and the roof pitch:
Peak height (inches) = (span ÷ 2) × pitch ÷ 12 × 12
Simplified: Peak height (inches) = (span in feet ÷ 2) × pitch
For a 28-foot span at 6/12 pitch: 14 × 6 = 84 inches = 7 feet of peak height above the top plate.
Steeper pitches increase peak height, which increases attic volume but also increases truss height, weight, and delivery complexity. Very steep trusses (10/12 and above) may require special delivery equipment or field assembly at the site. Low-pitch trusses (3/12 and below) are efficient to ship but require more careful snow load engineering in cold climates.
Top chord length is the hypotenuse of the half span and the rise:
Top chord per side = √(half-span² + peak-height²)
Add overhang length to get the full top chord from peak to tail.
Most residential trusses are spaced at 24 inches on center, which aligns with standard sheathing panel dimensions and minimizes truss count. Tighter spacing increases cost and labor but reduces the span demand on roof sheathing and ceiling drywall.
Check your local building code and roofing manufacturer requirements; some tile and metal roofing products require 16" OC framing or specific sheathing span ratings.
When ordering trusses from a manufacturer, be prepared to provide all of the following. Missing any detail can result in trusses that don't fit or require costly redesign.
Lead times for custom trusses typically run 2–6 weeks. Order early; truss delays are one of the most common causes of framing schedule slippage on residential projects.
Truss material cost is only part of the budget. Add delivery ($200–$600 depending on distance and quantity), crane rental ($400–$1,200 for a half day), and installation labor ($1.50–$3.00 per square foot of roof area). Gable-end trusses, valley sets, and hip sets are priced separately and should be confirmed with your supplier.
Need help estimating total project cost? Read our project cost estimation guide. For related framing tools, see our roof pitch calculator and our rafter calculator.