Free Construction Tool

Weight per Volume Calculator

Reviewed and updated: August 2026

Calculate the weight of any construction material by volume. Covers concrete, steel, lumber, gravel, soil, sand, brick, and more. Results in pounds, tons, and kilograms.

Density: 150 lb/ft³: Normal weight concrete
YOUR RESULTS
Weight (lbs)
—
pounds
Weight (tons)
—
US tons
Weight (kg)
—
kilograms
Density
—
lb/ft³
Volume (cu ft)
—
ft³
Volume (cu yd)
—
yd³

Use this calculator to find the weight of any common construction material by volume. Select a material, choose your volume unit, enter the amount, and get the weight in pounds, US tons, and kilograms instantly. Useful for truck load planning, structural load calculations, and delivery logistics.

Construction Material Weight Reference

Knowing the weight of construction materials is essential for three situations: planning truck loads (dump trucks have a weight limit, not just a volume limit), structural engineering (beams and floors must support the load above them), and equipment selection (can your skid steer or forklift handle this lift?).

Density Comparison at a Glance

The chart below shows how dramatically density varies across common construction materials. Steel is nearly 25 times denser than fiberglass insulation, which is why a small volume of steel can weigh more than a much larger volume of a lighter material.

DENSITY BY MATERIAL (LB/FT³) Steel 490 Aluminum 169 Concrete 150 Gravel 100 Brick 94 Sand 90 Topsoil 75 Oak 45 Pine 37 Fiberglass insulation 20

Density (weight per volume) is why equal-sized loads of different materials can require completely different handling equipment.

For a worked example: you're pouring a concrete slab 20 ft × 12 ft × 4 inches thick. Volume = 20 × 12 × (4 ÷ 12) = 80 cubic feet = 2.96 cubic yards. At 150 lb/ft³, that slab weighs 80 × 150 = 12,000 lbs (6 tons). A standard concrete truck holds 8–10 cubic yards, so one truck easily covers this pour: but if you're planning crane lifts or checking a floor's load capacity, knowing the 12,000 lb figure is critical.

Material Density Reference Table

MaterialDensity (lb/ft³)Density (kg/m³)Notes
Concrete (normal weight)1502,403Standard structural concrete
Concrete (lightweight)1161,858Expanded aggregate mix
Steel / Iron4907,849Structural steel, rebar, iron
Aluminum1692,707Approx. 1/3 the weight of steel
Gravel (dry)1001,6022,700 lbs per cubic yard
Gravel (wet)1051,682~5% heavier when saturated
Sand (dry)901,442Play sand is lighter than concrete sand
Crushed stone951,522#57 stone, crusher run
Topsoil (dry)751,2022,025 lbs per cubic yard dry
Topsoil (moist)901,442Can reach 2,400 lbs/yd³ wet
Clay soil951,522Dense and heavy when wet
Oak (dry)45721Hardwood: heavier than softwoods
Pine (dry)37593Common framing lumber
Brick (common)941,506Standard clay brick
Asphalt (compacted)701,121Varies by mix design
Fiberglass insulation20320Batt insulation, uncompressed

Why Material Weight Matters for Truck Load Planning

Dump trucks are rated by weight capacity, not just volume. A standard 10-wheel dump truck carries 10–14 tons. If you're ordering concrete at 150 lb/ft³, a 10-ton truck holds about 133 cubic feet: roughly 5 cubic yards. If you order gravel at 100 lb/ft³, the same truck carries about 200 cubic feet: roughly 7.4 cubic yards. Running the weight calculation before your order prevents costly second trips and overloaded vehicles.

Dead Load vs. Live Load: Why Material Weight Matters Structurally

In structural engineering, the weight of the building materials themselves (framing, concrete, roofing, drywall) is called dead load, a fixed, permanent weight the structure must support for its entire lifespan. This is distinct from live load, the variable weight of occupants, furniture, snow, and stored materials, which changes over time.

Building codes specify minimum design live loads for different room types (residential floors are typically designed for 40 psf, while decks and balconies often require 60 psf or more), but dead load is calculated directly from the actual materials specified in the design, which is exactly what this calculator helps estimate. Undersizing a beam or joist because dead load was estimated too low is a genuine safety issue, which is why engineers of record use code-specified or manufacturer-published density values rather than field approximations for final structural calculations.

Moisture Content Affects Weight Significantly

Wet materials weigh meaningfully more than dry. Moist topsoil can weigh 20% more than dry topsoil. Saturated clay soil can approach 120 lb/ft³ versus 95 lb/ft³ dry. If you're estimating truck loads after rain or planning structural loads in a water-retention scenario, always use the wet density figure.

Common Weight Estimation Mistakes

Structural note: For engineered load calculations (beam sizing, foundation design, floor load ratings), always use your local building code's specified dead load values rather than field estimates. The densities in this calculator are accurate typical values, but your engineer of record may use slightly different figures depending on the specific mix or grade of material specified.

Planning a related project? See our gravel calculator and excavation calculator.

Frequently Asked Questions
How much does a cubic yard of concrete weigh? ▾
Normal weight concrete weighs approximately 4,050 lbs (about 2 tons) per cubic yard. Lightweight concrete weighs about 3,132 lbs per cubic yard. These are the figures used for calculating structural dead loads and for planning concrete truck deliveries: a standard mixer truck holds 8–10 cubic yards, or 16–20 tons of concrete.
How much does a cubic yard of gravel weigh? ▾
Dry gravel weighs approximately 2,700 lbs (1.35 tons) per cubic yard. Wet gravel is about 2,835 lbs per cubic yard. Crushed stone runs about 2,565 lbs per cubic yard. These figures help you calculate truck loads when ordering bulk aggregates: a 10-ton truck holds roughly 7–8 yards of dry gravel.
How much does steel weigh per cubic foot? ▾
Structural steel weighs approximately 490 lbs per cubic foot (7,849 kg/m³): about 3.3× heavier than concrete. For rebar weight by bar size and length, use our rebar calculator which accounts for specific bar designations (#3 through #11).
How much does a cubic yard of topsoil weigh? ▾
Dry topsoil weighs about 2,025 lbs per cubic yard. Moist topsoil (typical delivery condition) weighs 2,200–2,400 lbs per cubic yard. This is important when planning deliveries: a 10-ton truck carries roughly 8–9 yards of moist topsoil, not the 10+ yards you might calculate assuming dry weight.
How much does lumber weigh per board foot? ▾
Dry pine (the most common framing lumber) weighs about 37 lb/ft³. One board foot is 1/12 of a cubic foot, so dry pine weighs roughly 3.1 lbs per board foot. A standard 2×4×8 stud, using actual dressed dimensions (1.5" × 3.5" × 96"), is about 3.5 board feet, so it weighs approximately 11 lbs dry. Green (wet) lumber can weigh 50–100% more, so a freshly cut 2×4×8 may weigh 16 to 22 lbs.
Why does concrete weigh so much more than the same volume of soil? ▾
Concrete's density (150 lb/ft³) comes from its composition: it's a mixture of cement, sand, gravel, and water that, once cured, has very few air voids and a dense, interlocked internal structure. Soil, by contrast, is a loose aggregation of particles with substantial air space between them, even when compacted. That's also why compaction matters so much in earthwork: compacting soil reduces air voids and increases density, which is why a compacted subgrade can support far more load than the same soil left loose.